How to configure wifi router? in the office for a few jobs, equipped with computers, or in an apartment where there is a desktop computer and a laptop, WiFi-router can be very useful.

Wifi-router - network device that is used to create a wireless network between computers, mobile devices (laptops, PDAs, tablets, mobile phones).It can also function as an access point Wi-Fi and Ethernet-router to connect your PC.

Configure WiFi-router, you can both work on the internal network, and to access the Internet.The following instructions are relevant for most models, but we recommend to specify the details in the instructions.

To configure the internal network and the Internet through a WiFi-router need these "ingredients»:

  • ready to connect to the Internet from the provider
  • computer with a network card
  • network cable to "Direct" crimp
  • router directly

router interface is usually four internal ports (LAN) and one external (WAN).In the external port cable is connected, by which the connection to the Internet.Inland ports are

used to connect computers to the internal network.

How to connect WiFi-router to the computer?

To begin with, we need to connect the router to your computer:

  1. Connect the router to a desktop PC or laptop with a network cable "direct" crimp (not crossover!).
  2. If the connection is successful, then the computer's network connections appear new network connection.Right-click, call the context menu and select the item in it «Properties» .Opens edit the properties of a network connection.
  3. In this window, select the "Internet Protocol (TCP / IP)» and click «Properties» , which opens the window for editing properties.
  4. Select «Use the following IP-address» (or similar, ie. E. Manual settings IP-addresses).
  5. Next, you must manually enter the following data:
  • IP-address: 192.168.0.2 (192.168.1.2)
  • Subnet Mask: 255.255.255.0
  • Default Gateway: 192.168.0.1 (192.168.1.1)
  • DNS:192.168.0.1 (192.168.1.1)

In this case, 192.168.0.1 or 192.168.1.1 - standard local IP-address assigned to wifi-router and 192.168.0.2 or 192.168.1.2 - local the IP-address.The manufacturer of the router can be specified other settings of the local IP, then you need to use them.

Check the correct IP-address, you can, with the command «ping».To do this, enter the command line Windows (Start- & gt; Run- & gt; cmd) and enter the following command:

& gt;ping 192.168.x.1 where 192.168.x.1 - local IP-address of the router

Setting Wifi-router

If the IP-address is pinged, then you can proceed to the next step - namely to set up wifi-router via webinterface.As a rule, the manual for the device states entering the router management interface.If such information is not available, it should be in the browser address bar enter the address http: //192.168.x.1.

On the next page you will be prompted to enter your login and password.These data should also be specified in the instructions.If not, you can try to login «admin», password - «admin» or empty.These are the standard username and password on most routers.

now available router administration panel.The device settings, select the section of WiFi (perhaps it will be called «wireless», t. E., "Wireless").Then select the current profile or create a new profile settings and provide the following information:

  • SSID: {name of your network}
  • Channel: auto
  • Wireless Mode: auto
  • Authentication Method: WPA-PSK
  • WEPEncrypting: TKIP
  • WPA Pre-Shared Key: Enter the password for access to the network

Other settings can be left in the meaning of "default".Then, you must restart the router via a Web interface and start configuring vayf on mobile devices: laptop, PDA, mobile phone and so on. D.

Connect the router to other devices

entering the wireless settings, you must manually register the IP-address, Subnet Mask, Gateway:

  • IP-address - is selected from the range of available addresses (192.168.0 / 1.0-255)
  • mask - 255.255.255.0
  • main gateway - 192.168. (0/1) .1

then save and apply the received settings, select the settings in the authorization WEP-encryption is authenticated and the type of WPA-PSK, and TKIP.After this is the password from the network and connect.

If you want to "give" in the internal network of Internet, it is necessary to connect a network cable coming from your ISP to the external interface on the router (for more details, see "How to distribute the Internet for WiFi» ).Then in the settings you need to specify the parameters of the external interface - those username and password issued by the provider.

In certain models, the settings may be slightly different, so carefully study the instructions to the device before setting WiFi-network.

How to configure wifi router?

Comment